LM1391N DATASHEET PDF

LMN Texas Instruments Phase Locked Loops – PLL datasheet, inventory, & pricing. LMN Datasheet PDF, pdf, pinout, equivalent, replacement, schematic, manual, data, circuit, parts, datasheet. National Semiconductor LMN: available from 2 distributors. Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing.

Author: Dakasa Tokus
Country: Denmark
Language: English (Spanish)
Genre: Spiritual
Published (Last): 7 February 2005
Pages: 430
PDF File Size: 19.51 Mb
ePub File Size: 14.3 Mb
ISBN: 314-7-66591-385-3
Downloads: 69558
Price: Free* [*Free Regsitration Required]
Uploader: Bragor

The voltage at Pin 16 determines the gain of the f-m intermediate frequency eatasheet higher values producing increased gain. The UCNA internal step logic activates one of four output sink drivers to step the load from one position to the next. They do not wash out in sunlight, although their reliability diminishes with the higher currents required in brightly lighted applications.

LMN Datasheet –

Signal level shifting is inexpensively accomplished with capacitors; the OFF reference, pull-up, and pull- down is done with a few discretes. Separate ground leads minimize decoupling problems. Additional loading may raise the overload point slightly, but AGC and sensitivity will be compromised. A d-c path of less than a must be provided between pins 4 and 6. There are problems associated with a non-standard configuration lack of sockets and higher prices and the smaller physical size will not aid the quest for higher power LEDs.

In all cases, the output is switched ON by an active high input level. Internal output pull-down resistors elimi- nate the need for external components usually re- quired for fluorescent display applications. The unit may have data inputs and a strobe bus see Figure 6. I toMvUMM 3 — 1. Input Capacitance c in Osc. Reducing the pin 16 voltage to 1. Type UDNB is in a pin dual in-line package with heat-sink contact tabs. The fifth I-F stage Q9 and Q10 is operated at maximum gain and current to provide full signal to the a-m and f-m detector.

1986_RCA_Linear_Integrated_Circuits 1986 RCA Linear Integrated Circuits

This poses no problem with the kQ input impedance of the ULNA since the cartridge manufacturer specifies the load impedance for full low-frequency response to less than 40 Hz.

In standard F-M radio applications, tuning-error muting eliminates the low-frequency thump and the noise tail as- sociated with tuning through a strong signal. The V N 0N voltage limit guarantees a minimum output source current per the specified conditions.

  EL DECALOGO KIESLOWSKI PDF

Balanced inputs eliminate ground loops which can cause stray coupling paths in discrete datsheet. BV, Note 4 — All outputs are pinned opposite their respective inputs to simplify circuit board layout. The maximum ton array. The feedback and ripple bypass capacitor at Pin 10 should be chosen for both low-frequency audio rolloff and supply lm139n1 rejection.

Type ULNA is designed to work within a range of supply voltages from 4. Gas discharge panels are a fine combination of aesthetics, reliability, low cost, large character size, multiplexing capability, etc.

LM1391N Datasheet PDF – National ->Texas Instruments

Overall negative feedback, set by the ratio of R33 to R32, is applied to the inverting input Q45 through an NPN emitter follower Q46 which also provides d-c level shifting.

Class B operation of the audio power amplifier yields high efficien- cy at rated output with very low quiescent power drain. The linear detection mode low signal level at pin 12as shown, is preferred for communications and other commercial applications, due to the preservation of the tuned circuit bandwidth and better rejec- tion of Gaussian noise.

Two apparent disadvantages now appear to exist: Applications The UHC- and UHD- Series, and power and relay drivers are ideally suited for driving incandescent lamps, relays, solenoids, and other interface devices with up to 1 A output current per package. The output transistors are capable of sinking mA and will sustain at least 50 V in the OFF state. Tech- niques similar dxtasheet those used for handling MOS devices should be employed. The AGC detector input pin 4 is connected through a small coupling capacitor to the mixer out- put.

PSoC Family Datasheet However, many of the high-current applications are within the capability of standard bipolar ICs now offered. All four devices incorporate input current limiting resistors and output suppression di- odes. The Series ULNA is especially designed for use with standard and Schottky TTL where higher output currents are required and loading of the logic output is not a concern.

  COURTLY LOVE OR WOMAN AS THING ZIZEK PDF

The sink driver should be allowed to go high turned OFF at least ns max. P D is dayasheet at the rate of 8. The bandwidth of the phase shift network peak separation is pri- marily defined by the Damping resistor R.

More accurately, the maximum input current for any collec- tor current is described by the equation: An increasing number of these Sprague devices are especially designed for or are easily adapted to motor darasheet applications. The ULNA audio amplifier stage has other input considerations to be taken into account for best results. Sprague CMOS devices feature input static protection but are still susceptible to damage when exposed to extremely high static electrical charges.

A copy of the quality control inspection plan used for specific dafasheet circuits is available on request. They are not intended for use with a-c sources, and will not sustain commercial a-c line voltages VAC.

The common low-level audio output can be used to drive any suitable audio power amplifier or stereo decoder e. There are three selections for each mode and nine possible combinations: These types are for general purpose applications such as motors, solenoids, relays, filaments, etc.

Voltage values shown in the test circuit waveforms are with respect to network ground terminal. Sprague Electric is a leading manufacturer of vol- ume integrated circuits serving the consumer, indus- trial controls, and peripherals markets.

The bipolar outputs may be used as segment, dot matrixbar, or digit drivers in vacuum fluorescent displays.

With either device, the input and enable levels must both be biased towards the positive supply to activate the output load. After an optimal F-M I-F gain is determined for a particular circuit design, the gain can be controlled with proper matching of the suffix and the pin 16 load. Both units feature open- collector outputs and in- tegral diodes for inductive load transient suppres- sion.

A d-c path of less than a must be provided between pins 2 and