EN25FQCP 8 Mbit Serial Flash Memory with 4kbytes Uniform Sector. 8 Mbit Serial Flash Details, datasheet, quote on part number: EN25FQCP . EN25F80 Datasheet PDF Download – 8 Mbit Serial Flash Memory, EN25F80 data sheet. Eon EN25F80 datasheet, 8 Mbit Serial Flash Memory (1-page), EN25F80 datasheet, EN25F80 pdf, EN25F80 datasheet pdf, EN25F80 pinouts.

Author: Kirg Meztigal
Country: Samoa
Language: English (Spanish)
Genre: Politics
Published (Last): 1 January 2013
Pages: 268
PDF File Size: 18.7 Mb
ePub File Size: 10.3 Mb
ISBN: 160-3-45049-328-7
Downloads: 99660
Price: Free* [*Free Regsitration Required]
Uploader: Kigazuru

Depending on the instruction, this might be followed by address bytes, or by data bytes, datawheet by both or none. And forgot to mention, this all started to work after a power cycle on the chip. I have verified my wiring.

For the detailed commands explanation and more in-depth information, please consult the included datasheet. Chip Select CS can be driven High at any time during data output. This releases the device from this mode.

EN25F80 Datasheet PDF

No matter what I read, address, status register, anything, it always comes up with 0. All other instructions are ignored while the device is in the Deep Power-down mode.

The Deep Power-down mode automatically stops at Power-down, and the device always Powers-up in the Standby mode. Before this can be applied, the bytes of memory need to have been erased to all 1s FFh.

The instruction set is listed in Table 4. High durability ofwrite cycles, data retention of 20 years, secure OTP memory block, high transfer speed, Datasheey mode for easy retrieval of IC-specific information. The address increment is automatically executed, making it possible to read the entire memory by a single Read Data command. This can be used as.

EN25F80 datasheet & applicatoin notes – Datasheet Archive

This datashete be achieved a sector at a time, using. To spread this overhead, the Page Program PP instruction allows up to bytes to be programmed at a time changing bits from 1 to datasheefprovided that they lie in consecutive addresses on the same page of memory. When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by driving the CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The EN25F80 can be configured to protect part of the memory as the software protected mode.


This product is no longer in stock.

EN25F80 Datasheet

This Data Sheet may be revised by subsequent versions 1 or modifications due to changes in technical specifications. Page Programming To program one data byte, two instructions are required: The Write In Progress WIP bit is provided in the Status Register so that the application program can monitor its value, polling it to establish when the previous Write cycle, Program cycle or Erase cycle is complete.

This is to ensure that the state of the internal logic remains unchanged from the moment dxtasheet entering the Hold condition. D Eon Silicon Solution, Inc. Status Register Bit Locations Note: When set to 1such a cycle is in progress, when reset to 0 no such cycle is in progress. Looking for customized version of this product? Any Read Identification RDID instruction while an Erase or Program cycle is in progress, is not decoded, and has no effect on the cycle that is in progress.

Progress WIP bit is provided in the Status Register so that the application program can monitor ddatasheet value. I salvaged a flash chip from a digital photo frame this morning. In the case of Page Program, if the number of byte after the command is less than 4 at least 1 data byteit will be ignored too.

The EN25F80 is designed to allow either single Sector at a time or full chip erase operation. Byte fields with data in parenthesis ” ” indicate data being read from the device on the DO pin.


Your cart is empty. Then, the 8-bit instruction code for the instruction is shifted in.

Read Data Instruction Sequence Diagram This Data Sheet may datasheft revised by subsequent versions or modifications due to changes in technical specifications. The Status Register contains a number of status and control bits that can be read or set as appropriate by specific instructions.

The Device ID can be read continuously.

Full text of “Datasheet: EN25F80”

The EN25F80 can be configured to protect part of the memory as the software protected mode. Register, Program or Erase cycle. Is this what is em25f80 my problem?

The minimum purchase order quantity for the product is 1. After successful write cycle, the state of the Write in Progress WIP bit is set to 0 automatically, and the device is ready to accept another erase or write instruction.

If less than Data bytes datashewt sent to device, they are correctly programmed at the requested addresses without having any effects on the other bytes of the same page.

The device identification indicates the memory type in the first byteand the memory capacity of the device in the second byte. Specifications Type Flash Applications Mass storage option in multimedia devices, data drives, non-volatile data storage in embedded applications, secure storage, and similar applications that require reliable permanent storage of digital information.

The primary difference between Mode 0 and Mode 3, as shown in Figure 3, concerns the normal state of the SCK signal when the SPI bus master is in standby and datssheet is not being transferred to the Serial Flash.