DMO565R DATASHEET PDF

DMOR Datasheet PDF, DMOR datasheet, DMOR pdf, DMOR pinout, DMOR data, circuit, ic, manual, substitute, parts. Description. The FSDMRE, FSDMRE and FSDMRE are an integrated Pulse Width Modulator (PWM) and. SenseFET specifically designed for. Features. • Optimized for Quasi-Resonant Converter (QRC). • Advanced Burst- Mode Operation for under 1W Standby. Power Consumption. • Pulse-by-Pulse.

Author: Mojar Moogugami
Country: Bahrain
Language: English (Spanish)
Genre: Career
Published (Last): 14 April 2018
Pages: 364
PDF File Size: 8.37 Mb
ePub File Size: 10.22 Mb
ISBN: 356-5-54118-515-6
Downloads: 10428
Price: Free* [*Free Regsitration Required]
Uploader: Nikogor

TempShutDown Delay Current vs.

At startup, an internal high voltage current source supplies the internal bias and charges the external capacitor Cvcc that is connected to the Vcc pin as illustrated in Figure 4. In this generation the startup resistor is replaced by an internal high voltage current source. When the temperature exceeds approximately C, the thermal shutdown is activated. However, even when the SMPS is in the normal operation, the over load protection circuit can be activated during the load transition.

When Vcc reaches 12V, the internal high voltage current source is disabled and the power is supplied from the auxiliary transformer winding. TempFeedback Source Current vs. In order to avoid undesired activation of OVP during normal operation, Vcc should be designed to be dmo565rr 19V. Published on Apr View Because of the pulse-by-pulse current limit capability, the maximum peak current through the Sense FET is limited, and therefore the maximum input power is restricted with a given input voltage.

  IP5200R MANUAL PDF

DMO565R PDF

Xmo565r that the 0. These parameters, although guaranteed, are tested in EDS wafer test process. The delay time for shutdown is the time required to charge CB from 2. Qlt datasheet pdf – datasheet pdf QLT datasheet, The typical soft start time is 10msec, The pulse width to the power switching device is progressively increased to establish the correct working conditions for transformers, inductors, and capacitors.

For stable operation, a capacitor should be placed between this pin and GND.

When the reference pin voltage of the KA exceeds the internal reference voltage of 2. These parameters indicate the inductor current. Free standing with no heat-sink under natural convection. Then, Vfb climbs up in a similar manner to the over load situation, forcing the preset maximum current to be supplied to the SMPS until the over load protection is activated.

SN datasheet – doctor- SN datasheet Author: Datasheet Release Date This pin is the positive supply voltage input. Texas Instruments – Subject: This device is an integrated high voltage power switching regulator which combine an avalanche rugged Sense FET with a current mode PWM control block.

DMOR PDF –

Datasheef start up, the power is supplied by an internal high voltage current source that is connected to the Vstr pin. In this manner, the auto-restart can alternately enable and disable the switching of the power Sense FET until the fault condition is eliminated see Figure 6.

  IATA DGD PDF

Comparing the feedback voltage with the voltage across the Fmo565r resistor plus an offset voltage makes it possible to control the switching duty cycle. This device is a basic platform well suited for cost effective designs of flyback converters.

DMOR Datasheet –

This reduces the dm5o65r through the opto-coupler LED, which also reduces the opto-coupler transistor current, thus increasing the feedback voltage Vfb. Therefore, the peak value of the current through the Sense FET is limited. If Vfb exceeds 2. Over load protectiontNormal operation Fault situation Normal operationFigure 6. At the instant the internal Sense FET is turned on, there usually exists a high current spike through the Sense FET, caused by primary-side capacitance and secondary-side rectifier reverse recovery.

Overload is defined as the load current exceeding a pre-set level due to an unexpected event. These parameters, although guaranteed at the design, are not tested in mass production. This parameter is the current flowing into the control IC.