ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Nikosar Kezragore
Country: Serbia
Language: English (Spanish)
Genre: Medical
Published (Last): 15 January 2008
Pages: 493
PDF File Size: 19.34 Mb
ePub File Size: 19.68 Mb
ISBN: 977-6-25402-984-4
Downloads: 3727
Price: Free* [*Free Regsitration Required]
Uploader: Gagore

D Yield strength is the stress at which an offset of 0. Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed.

C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming.

Link to Active This link will always route to the current Active version of the standard. SH – Machined from strain hardened stock or cold worked to develop the specific properties.

ASTM F594 Specification

A – Machined from annealed or solution annealed stock thus retaining the properties of the original material; or hot formed and solution annealed. B legend of conditions: Unless otherwise specified, all bolts, hex cap screws, and studs used wstm these nuts shall conform to the requirements of Specification F and shall be of the same alloy group.

  BELLASCOTIA SECRETS AND LIES PDF

R594 – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: A Tensile stress areas are computed using the following formula: ASTM Wstm covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening.

F When approved by the purchaser, alloys or Se may be furnished.

ASTM F Specification – Boltport Fasteners LLP

This abstract is a brief summary of the referenced standard. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. E When astmm by the purchaser, alloy F may be furnished.

The finished fasteners shall meet the applicable mechanical properties. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

ASTM does not give any warranty express or implied or make any representation that the contents of this f5994 are accurate, complete or up to date. A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4.

  CAMUS MITUL LUI SISIF PDF

Free Technical Information | Industrial Fasteners Institute

This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with Condition A, generally by the raw material manufacturer and thenc old worked to develop the specified properties.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Historical Version s – view previous versions of standard. Condition AF – When F5994 AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has been completed. A Minimum values except where shown as maximum or as a range.

Condition CW r594 When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.