ASTM D6484 PDF

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Fausar Faurisar
Country: Georgia
Language: English (Spanish)
Genre: Relationship
Published (Last): 15 March 2009
Pages: 404
PDF File Size: 7.95 Mb
ePub File Size: 13.32 Mb
ISBN: 718-9-92021-528-7
Downloads: 31712
Price: Free* [*Free Regsitration Required]
Uploader: Grokinos

NOTE 2—Experience has shown that? Properties that may be derived from this test method include open-hole notched compressive strength OHC. Guide plates are provided d4684 each side of the fixture to maintain alignment of the assembly. The specimen, typically, but not necessarily, a quasi-isotropic laminate, is 12″ long, 1.

The extensometers shall be essentially free of inertia lag at the speci?

Thus, data gathered using this test method may not translate directly into equivalent thickstructure properties. This chamber shall be capable of maintaining the d64884 section of the test specimen at the required test environment during the mechanical test.

Estimate the coupon strength to aid in transducer selection, calibration of equipment, and determination of equipment settings.

ASTM D Open-Hole Compression (OHC) Testing of CFRP Video | LabTube

The range of acceptable test laminates and thicknesses are described in 8. An optional threaded support plate is shown in Figs.

This laminate has relatively high stiffness with high notch sensitivity and was selected to produce high failure forces in order to evaluate the two loading methods using test laminate parameters representing the upper capability of the test method. Report both the nominal ratio calculated using nominal values and the actual ratio calculated with measured dimensions. Report the method of sampling.

  DEAD AID DAMBISA MOYO PDF

Practice E suggests that for this degree of con? Factors that influence the notched compressive strength and shall therefore be reported include the following: Subsequent Boeing specifications, and the ASTM standard, do not include these cutouts, strain gages not being used.

Report both the nominal where: Hydraulic wedge grips shall apply sufficient lateral pressure to prevent slippage between aatm grip face and the support? NOTE 6—The hole diameter is ignored in the strength calculation; the gross cross-sectional area is used. Results may also be affected by the ratio of hole diameter to thickness; the preferred ratio is the range from 1.

ASTM D6484 Compression Fixture for Fiber Composite Laminates| GD6484-113

If the specimen is to be failed, record the maximum c6484, the failure force, and the head displacement at, or as near as possible to, the moment of rupture. This may result in non-conservative data. Historical Version s – view previous versions of standard. Results may also be affected by the ratio of ungripped specimen length to specimen width; this ratio should be maintained at 2.

ASTM D Testing Fixture

Extensometers shall satisfy, at a minimum, Practice E 83, Class B-1 requirements for the strain range of interest, and shall be calibrated over that range in accordance with Practice E Use of these symbols is restricted to analytical dimensions when used with square brackets, as the symbols may have other de?

Combining values from the two systems may result in nonconformance with the standard. ASTM D Reference 5in the revision, added four holes in each end of the fixture for clamping bolts, as shown in Fig 4. A NASA standard, described in Reference 6, specifies a much wider 5″ wide specimen and thus is not commonly used, being less conservative of the material being tested.

  CONCRETO REFORZADO UN ENFOQUE BASICO DE EDWARD NAWY PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. However, since the notch dominates the strength, consistent preparation of the hole, without damage to the laminate, is important to meaningful results. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.

The velocity of the movable head shall be capable of being regulated in accordance with The long and short? However, cases such as elevated temperature testing of a moist specimen place unrealistic requirements on the capabilities of common testing machine environmental chambers.

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any xstm mentioned in this standard. In laminated composites, the principal material coordinate system has meaning only with respect to an individual orthotropic lamina. Combining values from the two systems may result in nonconformance with the standard.

Within the text the inch-pound units are shown in brackets. Shear loading is preferred in the Boeing specification, but requires relatively large hydraulic grips, i. It is d64844 responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Edgemounted extensometer displacement transducers are optional.