ASTM A480 PDF

ASTM A is the specification that covers the general requirements for flat- rolled stainless and heat-resisting steel plate, sheet and strip. It does not reference. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, product specifications that reference Specification A/. ASTM A/AM Standard Specification for General Requirements for Flat -Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and.

Author: Akibar Faular
Country: Great Britain
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 November 2008
Pages: 397
PDF File Size: 4.89 Mb
ePub File Size: 2.33 Mb
ISBN: 217-2-99430-751-5
Downloads: 27959
Price: Free* [*Free Regsitration Required]
Uploader: Dujas

This specification covers general requirements for flat-rolled stainless and heat-resisting steel plate, sheet, and strip. The manufacturer is permitted, if necessary, use a lower temperature resolution anneal or a stabilization anneal after a high temperature solution anneal in order to meet corrosion test requirements.

ASTM A480 Plate Thickness & Flatness Tolerances

These requirements shall apply to AM but shall not apply to A Historical Version s – view previous versions of standard. Use of this method shall be by agreement between purchaser and supplier.

All widths and lengths 1 16 18 1 16 18 Over mm 1. Refer to Section It is produced by buffing a? Bright Annealed Finish—See Note 4. sstm

This analysis shall be made from a test sample taken during the pouring of the melt, or from the in-process product later in the manufacturing? The producer is permitted to analyze for unspeci?

  KREONTOVA ANTIGONA PDF

This standard has been approved for use by agencies of the Department of Defense. C Not including hard tempers of 2xx and 3xx series, dead-soft sheets, and deep-drawing sheets.

NOTE 7—The term continuously, as applied to heat asttm, is meant to describe a heat-treating operation in which one cut length follows another through the furnace. It is neither practical nor necessary to specify limits for unspeci?

ASTM Specification A – What is it? – NKS

Within the text, the SI units are shown in brackets, except that when AM is speci? Quenched in water or rapidly cooled by other means at a rate sufficient to prevent reprecipitation of carbides, as demonstrable by the capability of passing the test for resistance to intergranular corrosion speci? Material Test Report and Certi?

The gage number shall not be a basis for rejection.

NOTE 2—If the longer dimension is under 36 in. The characters shall be of such size as to be clearly legible. D Quenched in water, except that coiled product heat treated in a continuous annealing line shall be water quenched or rapidly cooled by other means. Repair of Plate by Welding The allowable variation a408 a particular element in a single sample for product analysis is permitted to be either above or below the speci?

  CADPIPE TUTORIAL PDF

In the case of con? Link to Active This link will always route to the current Active version of the standard. The results of this retest shall be within the speci?

ASTM A480 Specification

Hard 19 16 13 26 19 16 12? Such requirements may include, but are not limited to, the following: If the hardness difference between the two ends of the coil exceeds 5 HRB, or equivalent, or if the material is temper rolled, tensile properties must be determined on both coil ends.

Various production methods may be used to obtain these? NOTE 2—Cold-rolled sheets in cut lengths a408 coils are produced in some type numbers and some widths and thickness to tolerances less than those shown in the table.

ASTM A Plate Thickness & Flatness Tolerances – Rolled Alloys, Inc.

Appearance will vary depending upon the starting? The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product speci?

For narrow strip, the following widths can be tested: