The 3G3MV is a miniature frequency inverter incorperating an open loop vector control Furthermore, the 3G3MV suppresses the revolution fluctuation caused. OMRON products are manufactured for use according to proper procedures by a qualified .. 3G3MV-P10CDT Operation Manual (this manual) and the CPM1/. A maximum of four errors can be displayed. U Software No. OMRON use only. U Output power. W. Monitors the output power of the Inverter (see note.
|Published (Last):||19 January 2012|
|PDF File Size:||20.87 Mb|
|ePub File Size:||19.14 Mb|
|Price:||Free* [*Free Regsitration Required]|
Preparing for Operation and Monitoring Chapter 3 Indicator Display Explanation sequence example If there is a parameter set value that does not coincide, the parameter number will flash. There are parameters that make setting unit changes when the values are increased with 3t3mv Digital Operator.
Port B Data No.
OMRON 3G3MV SYSDRIVE Inverter
A maximum of four errors can be displayed. Maintenance Operations Chapter 8 Warning Detection Nonfatal Error The warning detection is a type of Oron protective function that does not operate the fault contact output and returns the Inverter to its original status once the cause of the error has been removed.
Press the Enter Key so that the corresponding set value in the Inverter will flash. Communications Chapter 7 Byte No.
The value will be set in 0. Page List of Parameters Chapter 10 Emergency The Inverter stops according to the setting stop fault in n for interruption NO mode selection with the emergency stop input turned ON. Chapter 5 Basic Operation Setting Frequency References by Pulse Train Input By setting n omrom frequency reference selection to 5 for enabling the pulse train reference control terminal, frequency references can be executed by pulse 3f3mv input through the PR terminal.
Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information. Instead, the front cover is used as a terminal cover and two U-shaped cutouts are provided in place of the mounting holes.
Information added on enclosure ratings and motor capacity. 3g3mf
Omron SYSDRIVE 3G3MV User Manual
Each DSR message or response is divided into 8-bit blocks. Page 85 Preparing for Operation and Monitoring Chapter 3 Indicator Display Explanation sequence example 3g3mb there is a parameter set value that omrom not coincide, the parameter number will flash. LF This function detects open phases between the Inverter output and the motor.
If n for reverse rotation-prohibit selection is set to 1 reverse run prohibitedthe Inverter will not accept reverse-rotation commands. Use the Increment or Decrement Key to set the frequency reference.
Press the Enter Key.
Periodic Inspection S Installation: Doing so may result in damage to the product or malfunc- tion. Chapter 5 Basic Operation H Setting Frequency References 1 through 16 and the Inching Frequency Command n through n, n through n Frequency references 1 through 16 and an inching frequency command can be set together in the Inverter using registers n through n31, n through n Not doing so may result in electrical shock or fire.
Page Communications Chapter 7 Note 3.
Advanced Operation Chapter 6 PID Control Detected values of the Inverter in proportional, integral, and derivative PID control are fed back so that the values will coincide with preset target values. Function Data writing 1: Local ojron operated with the Digital Operator selection Note After this setting is made, mode selection with the Digital Operator is not possible. Preparing for Operation and Monitoring Chapter 3 3g3,v Name Probable cause Remedy Copy error An attempt was made to Check that the Inverters are copy or verify the parameter the same in voltage and set values while omronn control mode.
Ensure that the installation conditions are met. List of Parameters Chapter 10 Para Reg- Name Description Set- Unit Chan- Ref- Defaul t set- ister ting ges dur- ting range set- ence ting opera- page tion n Frequency Selects the frequency loss detection function for reference when the frequency reference from the control loss detec- circuit terminal suddenly drops.
Omron 3G3MV-AB (3G3MVAB) – Axdos AB | PLCSWEDEN | Automation Spare Parts
Trapezoidal and S-shape acceleration and deceleration are available. This manual also for: The default setting for the pin is OFF. Page 84 Preparing for Operation and Monitoring Chapter 3 If a set range error results, the corresponding parameter number will flash. Installation and Mounting Install the Inverter according to the installation conditions. Two types of command input methods are available.
The response will be comparatively slow if the target value changes because the feedback integral value is used. Error Overrun error 1: Error Framing error 1: Page List of Parameters Chapter 10 Para Reg- Name Description Set- Unit Chan- Ref- Defaul t set- ister ting ges dur- ting range set- ence ting opera- page tion n Frequency Selects the frequency loss detection function for reference when the frequency reference from the control loss detec- circuit terminal suddenly drops.
The frequency reference through analog input will be ignored if the Digital Operator has been selected for frequency reference settings. There is a label under the front cover indicating the arrangement of main circuit terminals. D Wires Used Use shielded, twisted-pair wires for wiring in order to prevent the Inverter from malfunc- tioning due to noise. Chapter 4 Test Run Caution Do not perform a signal check during operation.
Page Maintenance Operations Chapter 8 H The motor does not turn with input through the control terminals. Using the S-shape characteristic function for acceleration and decelera- tion can reduce shock to the machinery when stopping or starting. If the motor is running with no problems and the machinery system is vibrating with a high-pitched whine, it may indicate that this is occurring. The time required 0. Page Chapter 5 Basic Operation S1: This disconnection or faulty wiring.
Select Reverse for the conversion method. Note This parameter is monitored only. Be sure to follow the instructions given there. If the vibration cannot be suppressed after the differential time is set to 0.
The step number is automatically set. Set the level as a percentage, as fol- lows: IE Revision code The following table outlines the changes made to the manual during each revision.